How to Make a Pencil & Business Card Holder !!!

Add subtitles/CC
today I'm gonna show you how to make this combination business card holder
and pencil holder
I made my night at Maple and bingo it's a pretty quick and easy process is How to Make a Pencil & Business Card Holder !!! there's not a lot of complicated joinery involved
and just a few pieces that you just glue together now you may not learn any
groundbreaking
woodworking techniques this project but it's free easy to make
and they so well arts and crafts fairs and they also make great gifts
so let's get started
so now I'll take my three quarter inch stock and we saw them down
printing flyers middle over on my bandsaw to clean up the rough side the board
made by the band saw blade you can either run them through a drum sander
a planner for him playing the down on I'll take my core exp said maple
and refer to four inches for what will be the height about pencil holder
other take that same bored and Costco for
equal pieces at two and three-quarters inches so that need them to be equal
I'm using a stopped clock on my table fosler so now
over here my table saw I set my blade forty-five degrees
I'm going to cut a minor sample size and I'm going to do so
by sneaking up on cut by nineteen my fence over
until I get perfect mitre and then I will repeat that
on all fours East
so here program click the four sites the pencil holder
but instead of using clamps lenny is blue tape also line the inside
blue tape to prevent any squeeze out from getting on the wood and one more
thing
you might want to fan the inside before doing this sup
I'm just gonna lay out some tape here and I will set my pieces right on top of
that
insure to
align them nice and tight
now
was put some glue in the minors
group that in with my finger here
then
we will just rolled onto itself church nice and tight
and let that dry so now seven-story koresh round over BMI Roger
and they're ready round over the entire link that the board
I would then cut off the front and bath a business card holder
of this one boy here we go
and I think the board that I just ran through my router and ripped through
four inches
I will then cross cut two pieces at three and three-quarter inches
I would then take one other pieces and rip it down three eighths this will be
the fun in the business card holder
so after we take the tape off or pencil holder
will clean up the top and bottom over the dissenter if you don't have a
dissenter
you can use that he said Sam paper on top of a flat surface
while we still have our quarter inch crown overby
in the router Laura over the four sides in the pencil holder
along with the top
next willapa bay side have a bigger
eight inches by three and a half and will then round over the front and side
but I haven't gone over to help secure the pencil holder
will cut out a little answer that will go onto the base will use our pencil
holder to trace out the shape
so now I have my base and my answer
and the pencil holder that will sit over top of that answer I'm going to glue a
piece
I'll fabric on top %uh that answer
before I do this on top here and then to give a nice look cushion when you got
your pens and pencils and their
and issues and some elmer spirit he said it s
now cut off the excess with an exacto knife
another have my cancer body to go
I'm just gonna glued onto the base I'm use in CA Gly because it dries fast
even though I'm not going to top on yet
I'm going to use it to align that inserts
I'm just I Bonnie here to exactly where we want to go up
think I got it up
it's now
I'll just let that dry for a few minutes smell gonna go the pencil holder
onto the base and this guy had a little bit of glue around the edges here
and then use a brush to brush up along the sides have our answer
and just a touch on the bottom here
perfect
I'm not an easy clamps or anything I think I'm just gonna let that sat on
their
and right I will take a reagan clean out some that clueless Chris up a poder
for the business card holder
just went
eyeball i think's going to look good and for this part I'm going to you see a
good
you can use wood glue if you like but I like the fact that see a clue
dries really fast that looks good for the back
up
and let that dry
and that's it I need to do some final sanding
and had finish for mine I use a combination a boiled linseed oil and
polyurethane
they make great gifts and they also sell arts and crafts fairs
so I hope you like it thank you
mmm to keep up with me subscribe to my YouTube channel and follow me on
Facebook Google+ could pitcher tumbling Instagram
and at sea me should check out my website at growth and woodworker
dot com *** ***